Centers, Die Holder
1 internal, 1 external, 1 v, 1 1" die holder, Shop made. The arbor is # 1 MT and numbered 21532
Craftsman # Atlas #
Weight 1 lb's
FMT item # 111023-12
$45.00
Atlas Horizontal Mill Draw-in Bar
Atlas Part # M1-576
Weight 2 lb's
Newly Made by FMT
FMT item # atlm1-576
$55.00
Atlas Horizontal Mill Arbor Nut
M1-560-nut $35.00 each
This will fit the 7/8” or 1” Arbors
Newly made by FMT
FMT item # M1-560-nut
$35.00
ATLAS M1-560 Driver
Horizontal Mill Arbor Driver
Newly made by FMT and will fit the 7/8” or the 1”Arbor
FMT item # atlm1-560driver
$40.00
This page was last updated: May 17, 2012
Atlas Headstock Chuck
will fit the horizontal mill, 6" lathe or the Index centers # M1-200
for holding small diameter work No. 70 drill to 17/32 thru Headstock spindle.
1" x 10 tpi
atlas part # M6-375
Jacobs 56B
original box and in excellent condition
weight 4 lb's
FMT item # 111020-2
$145.00
6" Atlas Milling Attachment
The Atlas milling attachment is built extra-heavy to minimize vibration. can be swiveled completely to hold work at any angle. vise position is controlled by a feed screw with micrometer graduated collar - a gib take-up assures permanent accuracy. Vise slide is graduated and can also be swiveled to any desired angle. weight 10 lb's
Like new condition
atlas part # M6-500
Weight 9 lb's
FMT item # 111020-3
SOLD
Atlas Rocker
will fit the 6", 10” & 12" Tool Post,
Carriage Turret (670): Four-way Turret (673A) - Rocker, Back Slide Tool Post (676A) – Rocker
Made with oil Hardening tool steel
3/8” W x 2” L x .265” H with a radius of 2-1/2”
Hardened to 45c
Measure your post first to make sure it has not been replaced these rockers are made to replace atlas rockers only.
Made by FMT item # Atl670a
$12.00 each
Atlas Carriage Turret Stops
Fits the Atlas 670 Carriage Turret or the Atlas 800 Lever type Carriage Turret
Atlas Part # 9-674 & 5
Weight 2 lb's
FMT item #
$45.00
Atlas Face Plate
6" Face Plate 1-1/2""x 8 tpi
Original paint, will fit the 10" or 12" lathe
Weight 3 lb's
Atlas part # 9-15
FMT Item # 1110282
$ 35.00
ATLAS DRILL PRESS UNIVERSAL COMPOUND VISE
All kinds of accurate indexing, layout and spacing work straight lines, radial, circular - are handled by this versatile fixture. Built rigidly to adapt drill presses to light milling operations. Ideal for use with shapers, milling machines, lathes, and grinders for any jobs requiring accurate feeds in two directions.
Original paint, had service rust, has been cleaned and adjusted. new vise jaw make from o1 tool steel.
still has the orginal grind marks on table top.
Atlas part # w68
Weight 25 lb's
Item # 1202272
$275.00
Atlas Headstock Chuck
will fit the horizontal mill, 6" lathe or the Index centers # M1-200
for holding small diameter work No. 70 drill to 17/32 thru Headstock spindle.
1" x 10 tpi
atlas part # M6-375
Jacobs 56B
In excellent condition
2 in stock
weight 4 lb's
FMT item # 1110296A
$115.00
Marvin Vertical Mill Head
for the Atlas Horizontal Mill
V-1200G
the only thing missing is the guard, orginial paint, takes 3/8" tooling
Weight 14 lb's
FMT item # 11102813
Sold
Atlas Mill Lead Screw Nut
Atlas Part # M1-11
Made from Bronze Bearing Stock
Weight 1 lb's
Newly Made by FMT
FMT item # atlm1-11
$35.00
Atlas Rocker
newly made
will fit the 6", 10” & 12" Tool Post,
Carriage Turret (670): Four-way Turret (673A) - Rocker, Back Slide Tool Post (676A) – Rocker
Made with oil Hardening tool steel
3/8” W x 2” L x .265” H with a radius of 2-1/2”
Hardened to 45c
Measure your post first to make sure it has not been replaced these rockers are made to replace atlas rockers only.
Made by FMT item # Atl670a
$12.00 each
6" Atlas Cutter Holder
Holds milling cutter in heaadstock spindle. Includes draw bar, sleeve, arbor for 1/2" shank cutters. comes with one end mill bushing (3/8" 576C)
Like new condition
atlas part # M6-945
weight 2 lb's
FMT item # 111020-4
SOLD
6" Atlas Follower Rest
Insures accurate work on long slender rods. Mounts on back of carriage dovetail slide, follows the cutting tool, holds work in rigid position.
Like New Condition
atlas part # M6-395
weight 2 lb's
FMT item # 111020-7
$ 165.00
6" Atlas Steady Rest
Clamps to bed ways to support long pieces and insue accuracy in truning, boring and threading. Bronze jaws prevent scoring work. capacity 2 3/8" dia.
Like New Condition
atlas part # M6-326
weight 3 lb's
FMT item # 111020-6
SOLD
6" Atlas Draw-in Collet Chuck
w/collets
The most accurate method of chucking work between 1/32" and 9/32". hollow construction permits rods to be passed through lathe spindle. Handwheel control releases and tightens collet on work. Closing sleeve is ground inside and outside to assure maximum accuracy. comes with the 9 collets in the boxes, does not include the 4 extra show. This fits the temkin bearring lathe
Like New Condition
atlas part # M6-750
weight 4 lb's
FMT item # 111020-8
$ 325.00
6" Atlas Mica Undercutter
Unsurpassed for quick, easy, profitable precision workmanship on reconditioning armatures. Mounts on carriage cross slide - out of the way while you use regular lathe tools to true and polish the armature, moved into position instantly for undercutting. set of 10 undercutters never used.
Like New Condition
atlas part # M6-510a
weight 9 lb's
FMT item # 111020-10
$ 250.00
6" Atlas Armature Commutator Kit
Holds centerless armatures in lathe. Complete in metal case Includes headstock chuck with No.2 MT arbor, center rest chuck with No.1 MT arbor.
Like New Condition
atlas part # M6-441
weight 8 lb's
FMT item # 111020-9
$ 250.00
6" Atlas Gear Cutter
Mounts in your milling attachment. Place you blank on one end and a good gear on the other.end. Set up for 1/2" ID gears.
New Condition
atlas part # M6-
weight 3 lb's
FMT item # 111020-11
$ 220.00
6" Atlas Taper Attachment
This is not an orginnial atlas part this was made by a tool maker, tool steel and hardened and is very well made.
Atlas Part # M6-700
Weight 5 lb's
FMT item # 111021-1
$300.00
Tool Post Grinder Wheel Sharpener
Fits the 6" atlas lathe Made by a tool maker.
Used to sharpener your grinder wheel has a diamond cutter mounts on the lathe bed way.
Weight 2 lb's
FMT item # 111021-2
$75.00
Lathe Tool Bit Holder
Threading Bit
Fits the 6" atlas lathe Made with tool steal and hardened by a tool maker.
Used to hold your Threading tool bit when making threads that you can not disengage the half nuts you just flip up the bit and reverse the motor to bring it back to the starting point.
Weight 2 lb's
FMT item # 111021-3
$115.00
90 deg. V-Block
Fits the 6" atlas lathe Made with tool steal by a tool maker.
Mounts on a face plate so you can offset your work or hold difficult material.
Weight 2 lb's
FMT item # 111021-4
$65.00
Clamp Dog
This is not an original atlas part this was made by a tool maker, tool steel and hardened and is very well made. The center section rotates
Weight 1 lb's
FMT item # 111021-5
$40.00
Clamp Dog
Clamp type dog Has v-groves in center and a adjustable stud. looks to be made of cold rolled steal.
Weight 1 lb's
FMT item # 111021-7
$20.00
Round Boring Bar
Used between centers to bore.
5/8" dia.x 8"long has 3 holes for cutters
Weight 2 lb's
FMT item # 111021-8
$35.00
Square Boring Bar
3/8" x 7/16" x 4 3/4"Long
Has a 3/16" square hole for the cutter
Weight 2 lb's
FMT item # 111021-9
$25.00
Angle Plate Blank
Fits face plate made from steal .
Slots on one side only.
Weight 1 lb's
FMT item # 111021-6
$20.00
Atlas Dogs
Set of 4 dogs for diameters up to 1 1/2". Drop-forged steel. Hold work firmly.
Like new condition 1/2", 3/4", 1", 1 1/2" These where probably not made by atlas
Atlas Part # 142A
Weight 2 lb's
FMT item # 111022-1
SOLD
Center Ejector Bar
Steel w/brass tip, shop made for the 6" atlas lathe,
1/2" dia. x 10" long
It's the Bottom bar pictured
Weight 2 lb's
FMT item # 111022-3
$15.00
Jacobs Drill Chuck
6A 33 taper Cap. 0-1/2", #1 MT Jacobs Arbor, # 3 Jacobs Chuck Key
Like new
Weight 2 lb's
FMT item # 111022-4
$75.00
Albrecht Drill Chuck
0-1/8" 0-3mm drill chuck Made in germany, #1 MT Arbor made in germany
Very good condition
Weight 1 lb's
FMT item # 111022-5
$95.00
6" Atlas Hand Rest
Used for wood working Clamps to lathe bed I don't have the clamp only what is pictured.
This is the old style, no longer made, it still has the original paint.
Atlas Part # M6-300 / 6910
Weight 1 lb's
FMT item # 111022-6
SOLD
6" Atlas Tool Rest
Used for wood working, Set of two cast iron rests, on 4" wide, the other 8" wide. rests mount in T-slot of tool post slide. original paint, like new
Atlas Part # 6638A
Weight 1 lb's
FMT item # 111022-7
$45.00
Atlas 4" 3 jaw Universal chuck
In original box with Mounting Instructions, chuck key both sets of jaws some discoloration.1" x 10
like new condition
Atlas Part # 6611 / M6-845
Weight 5 lb's
FMT item # 111022-8
$195.00
Atlas 4" 4 jaw Independent chuck
In original box with Mounting Instructions, chuck key some discoloration.1" x 10
like new condition
Atlas Part # M6-884
Weight 5 lb's
FMT item # 111022-9
$175.00
Boring Tool Holder
for 6" Lathes made by Atlas sold by Sears
Clamp Ring, V-block, Plain Block and 1/2" Hig speed boring tool.
Craftsman # 1515 Atlas # M6-990
Weight 1 lb's
FMT item # 111022-10
SOLD
Tool Post Set
Made by Atlas sold by Sears.
9 piece set The 3/16" bar is not pictured.
Craftsman # 2038 Atlas # M6-380
Weight 1 lb's
FMT item # 111022-11
$130.00
Threading Tool
Drop-forged LH holder with blade ground to cut 60 deg. threads.
Has been used, very good condition
Craftsman # 9-2031 Atlas # M6-430
Weight 1/2 lb
FMT item # 111023-1
$60.00
Straight Tool Holder
3/16" Straight Tool Bit Holder
Unused Like New
Craftsman # 9-2033 Atlas # M6-139S
Weight 1/4 lb
FMT item # 111023-2
$40.00
Right Hand Turning Tool Holder
3/16" Straight Tool Bit Holder
Like New
Craftsman # 9-2034 Atlas # M6-139R
Weight 1/4 lb
FMT item # 111022-3
$35.00
Left Hand Turning Tool Holder
3/16" Straight Tool Bit Holder
Like New, tool bit not included
Craftsman # 9-2035 Atlas # M6-139L
Weight 1/4 lb
FMT item # 111023-4
$35.00
Right Hand Cut-off Tool
w/ Blade
Drop-forged holder with 3 1/4" high speed replaceable blade for quick, clean cut-offs.
Craftsman # 9-2037 Atlas # M6-590
Blade Craftsman # 9-2009 Atlas # M6-592
Weight 1/4 lb
FMT item # 111023-5
$55.00
Knurling Tool
Self-centering floating constructing heavy steel shank
New old stock in box
Craftsman # 9-2036 Atlas # M6-340
Weight 1/2 lb
FMT item # 111023-6
$80.00
Knurling Tool
Self-centering floating constructing heavy steel shank
Used, very good condition, no box
Craftsman # 9-2036 Atlas # M6-340
Weight 1/2 lb
FMT item # 111023-7
SOLD
Atlas Tailstock Wrench
Tail stock wrench also fits tool post
like new
Craftsman # Atlas # M6-115
Weight 1/2 lb
FMT item # 111023-8
$25.00
Drive Plate
#1 MT with 4 screw holes 2-1/4" dia.x 1/2" thick
it's use is for turning wood, shop made.
Craftsman # Atlas #
Weight 1 lb's
FMT item # 111023-9
$30.00
Work Arbor
For mounting chucks and holding grinding, buffing and wire scratch wheels,etc 1/2 x 20-thread, 2 steel flanges with nut on head end for clamping wheels MT#1, no box used very good condition
Craftsman # 9-2153 Atlas #
Weight 1 lb's
FMT item # 111023-10
$25.00
Work Arbor
For mounting chucks and holding grinding, buffing and wire scratch wheels,etc 1/2 x 20-thread, with nut on head end for clamping wheels MT#1, no box used very good condition
Craftsman # 9-2153 Atlas #
Weight 1 lb's
FMT item # 111023-11
$20.00
Drill Pad
Mounts in tailstock as a brace for drilling work with drill in headstock. # 1 MT, 2" dia.
Craftsman # Atlas #
Weight 1/2 lb
FMT item # 111023-13
$10.00
Arbor for Angular Cutter
Arbor for Cutter No. 574A
NOS
Craftsman # 1567 Atlas # 572
Weight 1/2 lb
FMT item # 111024-2
SOLD
Arbor for Angular Cutter
Arbor for Cutter No. 574B
NOS
Craftsman # 1566 Atlas # 567
Weight 1/2 lb
FMT item # 111024-3
SOLD
Angular Cutter
For face milling, dovetalling and cutting angles less than 90deg. included angle is 60deg.
NOS retail is $196.00
Craftsman # 29951 Atlas # 574A
Weight 1/2 lb
FMT item # 111024-4
$100.00
Angular Cutter
For face milling, dovetalling and cutting angles less than 90deg. included angle is 60deg.
NOS retail is $178.00
Craftsman # 29952 Atlas # 574B
Weight 1/2 lb
FMT item # 111024-5
$95.00
Cross Slide Stop
Clamps to cross slid dovetail to set depth of duplicate cuts.
This stop was altered from a 10" lathe stop. I could not tell at first that it was altered it's that good of a job.
Craftsman # Atlas #
Weight 1/2 lb
FMT item # 111024-7
$42.00
Cup Center
Supports work in tailstock. Replaceable center point. #1 MT. For wood turning
NOS
Craftsman # 9-21002 Atlas # L2-17
Weight 1/2 lb
FMT item # 111024-8
$20.00
Spur Center
For driving work mounted between centers. Replaceable center point. MT#1 for wood turning
NOS
Craftsman # 9-21062 Atlas # L2-16
Weight 1 lb's
FMT item # 111024-10
$25.00
Adapter Sleeve
No.2 MT to No.1MT
NOS
Craftsman # 9-21612 Atlas #
Weight 1/2 lb
FMT item # 111024-11
2 in stock
$20.00
60 deg. Headstock Center
No.2 MT Dead center, NOS
Craftsman # 9-21112 Atlas # 9-88
Weight 1/2 lb
FMT item # 111014-12
$20.00
Work Arbor
For mounting chucks and holding grinding, buffing and wire scratch wheels,etc 1/2 x 20-thread, 2 steel flanges with nut on head end for clamping wheels MT# 2, NOS
Craftsman # 9-2153 Atlas #
Weight 1 lb's
FMT item # 111024-13
$35.00
Work Arbor
For mounting chucks and holding grinding, buffing and wire scratch wheels,etc 1/2 x 20-thread, 2 steel flanges with nut on head end for clamping wheels MT# 1, NOS
Craftsman # 9-2153 Atlas #
Weight 1 lb's
FMT item # 111024-14
$30.00
Keyless Chuck
1/2" Cap. will screw on work aarbor 1/2"-20 thp
Made in japan
Craftsman # 9-22562 Atlas #
Weight 1 lb's
FMT item # 1110124-15
$25.00
Screw Center
for wood working No.1 MT
NOS
Craftsman # Atlas #
Weight 1 lb's
FMT item # 111024-16
$22.00
60 deg. Tailstock Center
No.1 MT dead center, NOS
Craftsman # 9-21102 Atlas # L2-80
Weight 1/2 lb
FMT item # 111024-17
$23.00
3/16" Cutter Bits
Pre-Ground, Set of Six High-speed cutters, RH turning, LH turning, RH facing, LH facing, roundnose, 60deg. V-thread.
NOS
Craftsman # 2043 Atlas # M6-386
Weight 1 lb's
FMT item # 111024-19
SOLD
10" Atlas Lathe Accessories
6" Atlas Lathe Accessories
Atlas Horizontal Mill Accessories
Atlas Shaper Accessories
Atlas Straight Tool Holder
Drop-forged special steel, accurately machined, heat-treated. 1/4" bits are required, 3/8" wide, Original paint, fits the 10" and 12" lathes
Atlas Part # 139
Weight 1 lb's
FMT Item # 1110284
$ 25.00
Atlas LH Tool Holder
Drop-forged special steel, accurately machined, heat-treated. 1/4" bits are required, 3/8" wide, Original paint, fits the 10" and 12" lathes
Atlas Part # 139
Weight 1 lb's
FMT Item # 1110286
$ 25.00
Atlas Cut-Off Tool
Quick, clean cut-offs. Drop-forged holder with 3/8" shank, Original paint, fits the 10" and 12" lathes
Atlas Part # 590
Weight 1 lb's
FMT Item # 1110285
$ 45.00
Atlas Straight Tool Holder
Drop-forged special steel, accurately machined, heat-treated. 1/4" bits are required, 3/8" wide, fits the 10" and 12" lathes Marked 9-139 in casting
Atlas Part # 139
Weight 1 lb's
FMT Item # 1110289
$ 20.00
Atlas LH Tool Holder
Drop-forged special steel, accurately machined, heat-treated. 1/4" bits are required, 3/8" wide, Original paint, fits the 10" and 12" lathes, Marked 9-139-L in casting
Atlas Part # 139L
Weight 1 lb's
FMT Item # 11102810
$ 20.00
Atlas Wrench 9" & 10"
original and in good condition
Works on the Shaper, Horizontal Mill, 10 ", 12" and Accessories.
atlas part # 9-115
Weight 1 lb's
FMT item # 1110297
$ 20.00
Atlas Mica Undercutter
For servicing armatures, Attaches to back of carriage cross slide where it can be put in action in a second or moved out of way when not in use. Original paint, fits the 10" and 12" lathes, comes with one cutter.
Atlas Part # 510A
Weight 11 lb's
FMT Item # 1110292
SOLD
6" lathe Tool Holder
Williams # 00L Turning Tool Holder, 3/16" bits, 5/16"w x 3/4" H, comes with wrench, very good condition.
Weight 1 lb's
FMT Item # 1110287
$ 25.00
Atlas Grinder Accessories
Atlas Valve Stem Attachment
This is all that I have on this item, you will have to make the other parts. Original paint, fits the 10" and 12" lathes
Atlas Part # 550
Weight 3 lb's
FMT Item # 1110293
$ 75.00
Atlas End Mill Holder
#2 MT 3/8"16 Tpi
Can be used on the Mill, clausing 8520, 8530 anything with a #2MT and /3/8-16 draw-bar
Weight 1 lb's
Atlas Part # Unknown
FMT item # 1110311
Sold
Atlas Side Pans
Very Rare
Attach to each side of stand to catch oil drippings as miller table moves. Heavy gage steel, mount to metal stand, original paint, there is some damage but can be repaired.
Weight 5 lb's
Atlas Part # 9051
FMT item # 1110311
$125.00
Atlas Shaper Vice
Swivels 360 deg., 4 hold-down bolts, Vice only no crank handle
Atlas Part # S7-VICE
Weight 15 lb's
FMT Item # 1110316
Sold
Atlas Extension Tool
For internal Work, Drop-forged holder.
do not have 1/2" bar
Like New
Atlas Part # S7-315
Weight 2 lb's
FMT Item # 1111017
$ 140.00
Atlas Drill Press Accessories
Atlas Lathe Dog
Marked 9-143-3/4 Has 3/4" Opening, forged steel
Atlas Part # 9-143
Weight 1 lb's
FMT Item # 1110312
SOLD
Milling Attachment # 500A
Atlas 10” & 12" Lathe
This Acc. equips the lathe for face milling, cutting keyways and slots, milling dovetails, squaring shafts. Can be swiveled completely to hold work at any angle.
very good Condition. & Cutter Holding Set only two end mill bushings 1/4", 3/8". Original paint.
Atlas Part # 500A & 945
Weight 22 lb's
FMT Item # 1110314
SOLD
Armature Chuck
Tail-stock armature chuck by Jacobs Mfg. Co., # 2 MT. Shank
Atlas Part #
Weight 6 lb's
FMT Item # 1110318
$50.00
Steady Rest
For 10" lathes, rigid support for accurately machining long pieces. clamps to bed ways. I do not have the bolt.
Atlas Part # 10-325
Weight 5 lb's
FMT Item # 1111014
1 in stock
$135.00
Screw Center
For facing and hollowing operations, #2 MT
Atlas Part # 352
Weight 2 lb's
FMT Item # 1111015
$20.00
Atlas Tool Holder
Shaper tool older, Uses 1/4" tool bits. 8 Positions.
Like New
Atlas Part # S7-139
Weight 1 lb's
FMT Item # 1111018
Sold
ATLAS shaping cutter adapter
used on drill press for wood working Comes with 2 chaping cutters
Atlas part # W6-6A
Weight 7 ozs
Item # 1202273
$ 25.00
ATLAS
Collet chuck 1/2" w/ 1/4" reducer
fits spindles with 33 Jacobs taper and has a locking ring. Can use any tool with a straight shank 1/2" or less dia. with the right reducer.
NOS
Sears part # 9 2467
Weight 1 lb's
Item # 1202274
$ 25.00
3 in stock
ATLAS HI-LO SPEED ATTACHMENT
It provides a low speed of 210 rpm for heavy metal work and higher than standard speeds for wood-working. Mounted on top of column takes 2 belts in place of the standard one. the belts that come with it need to be replaced. for 15" Drills with 2-1/2" ID Column dia. NOS
Atlas part # W-122
Weight lb's
Item # 1202275
Sold
ATLAS Drill Chuck
Jacobs 34-33C
NOS no key 33 Jacobs taper with a locking ring. this makes it suitable for wood working tools.
Atlas part #
Weight 2 lb's
Item # 1202276
$ 75.00
2 in stock
ATLAS
UNIVERSAL COMPOUND VISE Jaws
Atlas part #
Weight 3 lb's
Item # 1202277
SOLD
